无机盐工业
主管:中海油天津化工研究设计院有限公司
主办:中海油天津化工研究设计院有限公司
   中海油炼油化工科学研究院(北京)有限公司
   中国化工学会无机酸碱盐专业委员会
ISSN 1006-4990 CN 12-1069/TQ
研究与开发

锂离子电池石墨负极材料的包覆改性及电化学性能研究

  • 凌政 ,
  • 孙陆 ,
  • 田朋 ,
  • 叶俊伟
展开
  • 1.大连理工大学化工学院,辽宁 大连 116024
    2.辽宁省硼镁特种功能材料 制备及应用技术工程实验室,辽宁 大连 116024
凌政(2000— ),男,硕士,研究方向为石墨负极材料改性及其性能研究;E-mail:Lz1763026070@mail.dlut.edu.cn
叶俊伟(1979— ),男,博士,教授,研究方向为资源化工与先进功能材料;E-mail:junweiye@dlut.edu.cn

收稿日期: 2025-01-15

  网络出版日期: 2025-04-15

基金资助

国家自然科学基金项目(22378053);企业委托项目(HX20230646)

Study on coating modification and electrochemical performance investigation of graphite anode materials for lithium-ion batteries

  • LING Zheng ,
  • SUN Lu ,
  • TIAN Peng ,
  • YE Junwei
Expand
  • 1. School of Chemical Engineering,Dalian 116024,China
    2. Liaoning Province Magnesium Special Functional;Material Preparation and Application Technology Engineering Laboratory,Dalian University of Technology,Dalian 116024,China

Received date: 2025-01-15

  Online published: 2025-04-15

摘要

石墨是重要的锂离子电池负极材料,但天然石墨的初始库伦效率低、循环稳定性和倍率性能较差等缺点限制其应用。为了提高石墨结构稳定性及其电化学性能,以Al(NO33·9H2O为铝源,利用氨水调节pH,采用沉淀法在石墨表面均匀包覆一层Al(OH)3,并进一步热处理制备Al2O3包覆石墨负极材料。此方法与原子层沉积法相比,具有过程简单和成本低廉的优点,比溶胶-凝胶法反应进程更好控制且能耗更低。当Al2O3包覆质量分数为1.03%时,获得表面光滑的改性石墨,Al2O3包覆层可起到预成型固态电解质界面(SEI)的作用,降低SEI膜的再生及锂离子的损耗。电化学性能试验表明,该材料在充放电过程中表现出优异的倍率性能及循环稳定性,将原料石墨和1.03%(质量分数)Al2O3包覆改性的石墨负极材料分别与锂片组装成锂离子电池,在0.1C(1.0C=372 mAh/g)的电流密度下,充放电循环100次后,其比容量分别为212.59 mAh/g和354.37 mAh/g,容量保持率分别为67.99%和98.59%。

本文引用格式

凌政 , 孙陆 , 田朋 , 叶俊伟 . 锂离子电池石墨负极材料的包覆改性及电化学性能研究[J]. 无机盐工业, 2025 , 57(12) : 18 -25 . DOI: 10.19964/j.issn.1006-4990.2025-0021

Abstract

Graphite is an important anode material for lithium-ion batteries,but the low initial coulombic efficiency,short cycle life,and poor rate performance of natural graphite limit its application.In order to improve the stability of its graphite structure and electrochemical performance,Al(NO33·9H2O was used as the aluminum source with adjusting the pH with ammonia water and uniformly coating a layer of Al(OH)3 on the surface of graphite by precipitation method,and Al2O3 coated graphite anode material was further prepared by heat treatment.Compared with the atomic layer deposition method,this method had the advantages of simple process and low cost,better control of the reaction process and lower energy consumption than the sol gel method.When the Al2O3 coating mass was 1.03%,the modified graphite surface was smooth.The Al2O3 coating layer could serve as a preformed solid electrolyte interface(SEI),reducing the regeneration of SEI and the consumption of lithium ions during subsequent cycling processes.Electrochemical performance tests showed that the materials exhibited excellent rate performance and cycling stability during charge and discharge processes.Graphite and Al2O3 coated graphite anode materials with a modification amount of 1.03% were assembled with lithium sheets to form lithium-ion batteries.After 100 cycles of charge and discharge at a current density of 0.1C(1.0C=372 mA∙h/g),the specific capacities were 212.59 mA∙h/g and 354.37 mA∙h/g,with capacity retention rates of 67.99% and 98.59%,respectively.

参考文献

[1] SAHU S R, RIKKA V R, HARIDOSS P,et al.A novel α-MoO3/single-walled carbon nanohorns composite as high-performance anode material for fast-charging lithium-ion battery[J].Advanced Energy Materials202010(36):2001627.
[2] XIE Jing, LU Yichun.A retrospective on lithium-ion batteries[J].Nature Communications202011:2499.
[3] LI Junhao, LIU Zhongqi, WANG Yifan,et al.Investigation of facial B2O3 surface modification effect on the cycling stability and high-rate capacity of LiNi1/3Co1/3Mn1/3O2 cathode[J].Journal of Alloys and Compounds2020834:155150.
[4] SCHMUCH R, WAGNER R, H?RPEL G,et al.Performance and cost of materials for lithium-based rechargeable automotive batteries[J].Nature Energy20183(4):267-278.
[5] GUO Jianguang, LU Shicheng, XIE Junran,et al.Preparation of mesophase pitch with domain textures by molecular regulation of ethylene tar pitch for boosting the performance of its carbon materials[J].Journal of Analytical and Applied Pyrolysis2023170:105932.
[6] ZHANG Jie, ZHOU Chen, NAENEN V,et al.Facile synthesis of dual-phase lithium titanate nanowires as anode materials for lithium-ion battery[J].Journal of Alloys and Compounds2021875:160038.
[7] DU Aimin, LI Hang, CHEN Xinwen,et al.Recent research progress of silicon-based anode materials for lithium-ion batteries[J].ChemistrySelect20227(19):e202201269.
[8] WU Chenghao, ZHU Guanjia, WANG Qiong,et al.Sn-based nanomaterials:From composition and structural design to their electrochemical performances for Li- and Na-ion batteries[J].Energy Storage Materials202143:430-462.
[9] PAN Yue, TONG Kun, TIAN Ruyu,et al.Advanced anode materials based on iron oxides for lithium-ion batteries[J].Nano202318(6):2330004.
[10] LEI Tongfei, WANG Yinwei, PAN Feng,et al.Nanofibrous carbon@cobaltous oxide composites for high electrochemical performance as anode materials of lithium-ion batteries[J].Ionics202127(12):5097-5101.
[11] WANG Zhijun, ZHANG Bingjie, ZHANG Yueyan,et al.A novel π-conjugated poly(biphenyl diimide) with full utilization of carbonyls as a highly stable organic electrode for Li-ion batteries[J].RSC Advances202010(52):31049-31055.
[12] 张珊珊,曾雨乐,张婷,等.锂离子电池正极预锂化技术研究进展[J].无机盐工业202557(1):1-13,26.
  ZHANG Shanshan, ZENG Yule, ZHANG Ting,et al.Research progress of cathode pre-lithiation technology for lithium-ion batteries[J].Inorganic Chemicals Industry202557(1):1-13,26.
[13] GOODENOUGH J B, PARK K S.The Li-ion rechargeable battery:A perspective[J].Journal of the American Chemical Society2013135(4):1167-1176.
[14] LIU Hanlin, YANG Wang, CHE Sai,et al.Silicon doped graphene as high cycle performance anode for lithium-ion batteri- es[J].Carbon2022196:633-638.
[15] XIONG Dongbin, LI Xifei, BAI Zhimin,et al.Superior cathode performance of nitrogen-doped graphene frameworks for lithium ion batteries[J].ACS Applied Materials & Interfaces20179(12):10643-10651.
[16] ZHANG Chenzhen, MAHMOOD N, YIN Han,et al.Synthesis of phosphorus-doped graphene and its multifunctional applications for oxygen reduction reaction and lithium ion batteries[J].Advanced Materials201325(35):4932-4937.
[17] LI Qiuya, LI Bin, LV Dongjun,et al.Synthesis of copper naphthalocyanine/graphene oxide composites as anode materials for lithi-um-ion batteries[J].Physical Chemistry Chemical Physics202325(45):31178-31187.
[18] MüLLNER S, HELD T, TICHTER T,et al.Impact of functional groups in reduced graphene oxide matrices for high energy anodes in lithium-ion batteries[J].Journal of the Electrochemical Society2023170(7):070523.
[19] HE Yu, YU Xiqian, WANG Yanhong,et al.Alumina-coated patterned amorphous silicon as the anode for a lithium-ion battery with high coulombic efficiency[J].Advanced Materials201123(42):4938-4941.
[20] YAN Shuaipeng, XU Jiahao, BIAN Yuhan,et al.Effects of Al2O3 coating on electrochemical performance of MCMB material and LiNi0.5Mn1.5O4/MCMB full cells[J].Journal of Materials Science:Materials in Electronics202334(4):271.
[21] WANG Shidi, LI Yang, WANG Lijun,et al.PVA generated carbon-coated natural graphite anode material for enhanced performances of lithium-ion batteries[J].Ionics202430(11):6845-6853.
[22] FENG Tianyu, XU Youlong, ZHANG Zhengwei,et al.Low-cost Al2O3 coating layer as a preformed SEI on natural graphite powder to improve coulombic efficiency and high-rate cycling stability of lithium-ion batteries[J].ACS Applied Materials & Interfaces20168(10):6512-6519.
[23] JUNG Y S, CAVANAGH A S, RILEY L A,et al.Ultrathin direct atomic layer deposition on composite electrodes for highly durable and safe Li-ion batteries[J].Advanced Materials201022(19):2172-2176.
[24] JUNG Y S, CAVANAGH A S, DILLON A C,et al.Enhanced stability of LiCoO2 cathodes in lithium-ion batteries using surface modification by atomic layer deposition[J].Journal of the Electrochemical Society2010157(1):A75.
[25] KIM D S, KIM Y E, KIM H.Improved fast charging capability of graphite anodes via amorphous Al2O3 coating for high power lithi-um ion batteries[J].Journal of Power Sources2019422:18-24.
[26] 田朋,张浩然,徐金钢,等.氧化铝溶胶改性锂离子电池正负极材料的研究[J].无机盐工业202456(9):44-53,116.
  TIAN Peng, ZHANG Haoran, XU Jingang,et al.Study on aluminum sol modified anode and cathode materials for lithium ion batteries[J].Inorganic Chemicals Industry202456(9):44-53, 116.
[27] DAN Jianglei, JIN Chenxin, WEN Lijun,et al.A double-layer-coated graphite anode material for high-rate lithium-ion batteri- es[J].Solid State Sciences2023141:107220.
[28] SHI Qiang, HENG Shuai, QU Qunting,et al.Constructing an elastic solid electrolyte interphase on graphite:A novel strategy suppressing lithium inventory loss in lithium-ion batteries[J].Journal of Materials Chemistry A20175(22):10885-10894.
[29] ZOU Feng, CUI Zehao, NALLAN H C,et al.Long-term cycling of a Mn-rich high-voltage spinel cathode by stabilizing the surface with a small dose of iron[J].ACS Applied Energy Materials20214(11):13297-13306.
[30] ZHANG Jie, WANG Rui, YANG Xiaocheng,et al.Direct observation of inhomogeneous solid electrolyte interphase on MnO anode with atomic force microscopy and spectroscopy[J].Nano Letters201212(4):2153-2157.
[31] ALI Y, IQBAL N, SHAH I,et al.Mechanical stability of the heterogenous bilayer solid electrolyte interphase in the electrodes of lithium-ion batteries[J].Mathematics202311(3):543.
[32] LI Jialin, WANG Yanan, SUN Shuyu,et al.Understanding and regulating the mechanical stability of solid electrolyte interphase in batteries[J].Advanced Energy Materials202515(4):2403845.
[33] SHI Qiang, LIU Weijie, QU Qunting,et al.Robust solid/electrolyte interphase on graphite anode to suppress lithium inventory loss in lithium-ion batteries[J].Carbon2017111:291-298.
[34] MA Huirong, YU Zhongrui, CHEN Jingjing,et al.Incorporating α-Al2O3 nanodots into expanded graphite anodes toward stable fast charging for lithium-ion batteries[J].ACS Applied Energy Materials20236(3):1389-1395.
[35] XU Tao, ZHOU Chengkun, ZHOU Haihui,et al.Synthesis of alumina-coated natural graphite for highly cycling stability and safety of Li-ion batteries[J].Chinese Journal of Chemistry201937(4):342-346.
文章导航

/